Touch COP
1. Product Introduction(below picture is for reference)
The ETOUCH capacitive touch control screen product series adopts a high-sensitivity touch sensing system and equipped with a bright full-view display screen. The glass surface structure has no known wear mechanism, which overcomes the easy wear characteristics of traditional touch screens (not less than 50 million clicks); no external signal transfer board is required, and the elevator floor status can be displayed synchronously; the traditional button matrix is replaced by a numeric keyboard , Personalized customized product structure and interface, which can be designed with various car styles to meet the needs of high-end customers.
Available pictures, videos, and streaming media to meet the needs of various graphic display, information release, and commercial advertising;
Optional voice call elevator function, no need to contact, simple dialogue control the elevator to reach the designated floor and control the door switch;
Multiple relay modules can be configured to control the operation of external equipment.
Product Parameter
ETOUCH-104-IN
Electrical specifications | |
Attributes | Parameter |
Model | ETOUCH-104-IN |
Size | 10.4inch |
Resolution ratio | 768×1024 |
Available display area | 160×213 |
View | Horizontal/Vertical ±80° |
Bright(cd/㎡) | 350 |
Comparison rate | 1200:1 |
ETOUCH-120-IN
Electrical specifications | |
Attributes | Parameter |
Model | ETOUCH-120-OUT |
Size | 12.1inch |
Resolution ratio | 768×1024 |
Available display area | 186×247 |
View | Horizontal ±80 °/vertical ±70° |
Bright(cd/㎡) | 500 |
Comparison rate | 700:1 |
ETOUCH-185-IN
Electrical specifications | |
Attributes | Parameter |
Model | ETOUCH-185-OUT |
Size | 18.5inch |
Resolution ratio | 1080×1920 |
Available display area | 230×409 |
View | Horizontal/vertical ±70° |
Bright(cd/㎡) | 300 |
Comparison rate | 800:1 |
ETOUCH-285-IN
Electrical specifications | |
Attributes | Parameter |
Model | ETOUCH-285-OUT |
Size | 28.5inch |
Resolution ratio | 540×1920 |
Available display area | 197×699 |
View | Horizontal/vertical ±80° |
Bright(cd/㎡) | 500 |
Comparison rate | 4000:1 |
ETOUCH-370-IN
Electrical specifications | |
Attributes | Parameter |
Model | ETOUCH-370-OUT |
Size | 37inch |
Resolution ratio | 540×1920 |
Available display area | 253×900 |
View | Horizontal/vertical ±80° |
Bright(cd/㎡) | 700 |
Comparison rate | 4000:1 |
Parameters and configuration
Material | Glass |
Operation | Touch |
Installation | Embedded/Customized |
Connection | Contact/ protocol |
Interface | Serial/ parallel/ custom |
Output interface | RS485（connect to button board） |
Interface upgrade | TF card/ USB |
Voltage | DC 24V |
Relay dry contact voltage | ≤DC36V |
Rate | 10.4 Inch/12.1 Inch：≤15W |
Working temperature | -20~60℃ |
Humidity | 10~90%RH |
Storage temperature | -20~70℃ |
Product Function
1) Call elevator function
Touch-type elevator floors selection and door control, etc., dynamic background bright display effect
2) Elevator operation information display
Elevator landing information, running direction display
3) Elevator customized information display
Display customized LOGO, date, week, time, alarm information, rated load and number of people information, etc.
4) Multimedia information display
Advertising picture and video display function; real-time streaming media advertisement, weather display function (optional, network support required)
5) Firmware upgrade
Through the TF card slot/USB interface, users can change the background content and program upgrades by themselves, which is easy to operate.y to operate.
Product Interface
a. 485 signal output interface
Remark: The 485 interface is used to connect to the touch screen key control board, using a 3.81 pitch 4-bit green socket
Pin No. | 1 | 2 | 3 | 4 |
Definition | 24V | GND | B | A |
b. Power and communication interface
It depends on the specific elevator, usually including CAN or RS485, etc.
Connection diagram
(1) Button board
(2) Dial code
DIP switch | Function | Label | |||
S1 | S2 | S3 | S4 | ||
OFF | OFF | OFF | OFF | First board | Corresponding to actual floors 1-16 |
ON | OFF | OFF | OFF | Second board | Corresponding to actual floors 17-32 |
OFF | ON | OFF | OFF | Third board | Corresponding to actual floors 33-48 |
ON | ON | OFF | OFF | Fourth board | Corresponding to actual floors 49-64 |
OFF | OFF | ON | OFF | Fifth board | Corresponding to actual floors 65-80 |
Note
Each button interface board is connected to 16 floors at most, and the actual floor corresponding to each board is subject to the label on the button interface board.
Control principle: The touch screen uses the RS485 signal to control the relay on the button interface board to simulate the call action of the mechanical button, and read the light signal of the mechanical button to record the registered floor information.
(3) Wiring of LCD screen equipment and touch screen keypad
The accessories include the button interface board communication line and the button interface board (the quantity depends on the actual floor). Plug the end of the button interface board communication line into the "transfer board data interface" of the touch screen, and the other side is connected to the button interface board On the "Power and Data Interface".
(4) Connection of the button
The button output port definition is clearly marked on the back of the interface board
PIN | 1 | 2 | 3 | 4 |
Definition | Switch dry contact | Negative of indicate light | Positive of indicate light | |
Note: The dry contact supports up to 36V. The dry contact switch is a normally open point
Testing, packaging and shipping
1. Appearance quality inspection
a. The clear silk screen on the electronic board;
b. The components on the electronic board must not be loose or soldered;
c. The clear silk screen of the components on the electronic board;
d. The information display device on the electronic board has a smooth appearance, no scratches and color spots;
Basic function inspection
It is required to be able to meet "maintaining good performance, all actions, malfunctions, and maintenance of functional actions".
Product packaging
The electronic board adopts anti-static packaging to prevent scratches. Avoid violent vibrations during the handling process
Contact
Technology:
