江苏春晨电缆有限公司：https://www.afzhan.com/st159127/
1 range
本规范规定了采购“导电炭黑”材料的要求、试验方法、检验规则、包装、标志、运输及贮存。
This specification specifies requirements, test methods, inspection rules, packaging, marking, transportation and storage of "conductive carbon black" materials.
2 要求和试验方法，JFEYH10KV高压电机引接线
2 requirements and test methods
导电炭黑的要求和试验方法符合表1规定。
The requirements and test methods of conductive carbon black conform to the requirements of Table 1.
表1 导电炭黑的要求和试验方法，，JFEYH10KV高压电机引接线
Table 1 requirements and test methods for conductive carbon black
序号 试验项目 单位 性能指标 试验方法，
Test method for unit performance index of serial number test item
1 比表面积 m2/g 114 GB/T 3780.5
1 specific surface area m2/g 114 GB/T 3780.5
2 吸油值 ml/g 1.3 GB/T 3780.2
2 oil absorption value ml/g 1.3 GB/T 3780.2
3 pH值 — ≥7 GB/T 3780.7
3 pH value is greater than or equal to 7 GB/T - 3780.7
4 加热减量 % 1.5～2 GB/T 3780.8
4 heating reduction% 1.5 ~ 2 GB/T 3780.8
5 灰分 % ≤0.5 GB/T 3780.10
5 ash% less than or equal to 0.5 GB/T 3780.10
6 杂质 % 无 GB/T 3780.12
6 impurity% no GB/T 3780.12
3 检验规则
3 inspection rules
3.1 检验方法及要求
3.1 inspection methods and requirements
3.1.1 对于定点厂家供应的导电炭黑，产品性能稳定，作隔批抽检。
3.1.1 for the supply of conductive carbon black manufacturers, the product performance is stable, for sampling.
3.1.2 对于新厂家供应的导电炭黑，应每批抽检，连续5次抽样均合格，转隔批抽检。
3.1.2 for the supply of new manufacturers of conductive carbon black, should be every batch of sampling, continuous sampling of 5 are qualified, to separate batches of sampling.
3.1.3 抽样方法
3.1.3 sampling method
每批任取一包。
Each batch to take a package.
3.2 检测项目
3.2 test items
3.2.1 可检项目为加热减量、PH值、灰分、杂质。
3.2.1 can be seized items for heating reduction, pH value, ash, impurities.
3.2.2 对于无法检测的性能依据生产厂家的检测报告或质保书验收，并进行定期委外检测。
3.2.2 for the performance of the test can not be based on the manufacturer's test report or the quality of the acceptance of the book acceptance, and regular outsourcing testing.
4 包装
4 packaging
用内袋是三层牛皮纸，外袋是二层牛皮包装，应完整无破损，防潮防污染。
With the inner bag is three layers of kraft paper, the outer bag is two layers of kraft packaging, should be complete without damage, moisture and anti pollution.
5 标志
5 mark
包装外应印有：产品名称、批号、生产日期、净重、生产厂名
Packaging should be printed with: product name, batch number, production date, net weight, the name of the factory
6 附件
6 attachment
产品进厂时，随货应有材料生产厂家质量保证书或质量检验单，*供货时，必须附有法定部门的型式试验报告。正常供货时，每年应提供一次法定部门的型式试验报告。
When the product enters the factory, along with the goods should have the material manufacturer quality assurance book or the quality inspection sheet, the first time, must have the legal department the type test report. When the normal supply, the annual report of the type test of the legal department should be provided.
7 运输
7 transportation
运输时避免碰撞破损、防混放。
Avoid collision damage and prevent mix.
8 贮存
8 storage
应该存于通风良好，阴凉干燥、防潮的库房内，并注意防破包造成污染。
Should be stored in a well ventilated, cool and dry, damp proof warehouse, and pay attention to prevent damage caused by pollution.
