DE10型冲板流量计可检测量从0.75吨/小时到80吨/小时的散装物料。采用的支撑系统及波形弹簧，保证了检测板只能被限制在水平方向运动。这个位移能被高分辨率的传感器所检测，传感器会输出一个电压信号，这个电压信号会被转换成免受噪音影响的脉冲频率调制数字信号。
优点
· 的设计可允许流量计安装在的工况中
· 测量不受检测板上冲击点改变的影响
· 检测板上的物料堆积不影响零点
· 高可靠性，低维护
· 配有机械式减振系统以吸收冲击或减弱振动
· 传感器安装在一个外壳中，与料流隔离
· 对于脉冲性或波动性料流也能精确的测量
定制的冲板流量计箱体
徐州威泰克可专门为客户设计箱体以满足用户的特殊要求。这些箱体可以和现有的法兰连接。此外，它们更易于安装，通常只需占用很小的空间，而且可以保证冲板流量计实现的工作性能。
徐州威泰克可专门为客户设计箱体以满足用户的特殊要求。这些箱体可以和现有的法兰连接。此外，它们更易于安装，通常只需占用很小的空间，而且可以保证冲板流量计实现的工作性能。
规格及参数
测量范围：0-25吨/小时～0-800吨/小时
标准温度：+10℃～＋80℃(可提供更低或更高的温度配置)
物料温度： +10℃～＋80℃
认证(可选)：FM认证，Ⅰ和Ⅱ级1和2部分A-G组，仅在安全区域与威泰克WTC2106或MT2106仪表结合使用
FM认证，Ⅰ和Ⅱ级1和2部分A-G组，仅在安全区域与威泰克WTC2106或MT2106仪表结合使用
偏移测量：线性差动变换器测量
无检测板重量：61公斤
防尘：从检测板外壳开始*密封
标准温度：+10℃～＋80℃(可提供更低或更高的温度配置)
物料温度： +10℃～＋80℃
认证(可选)：FM认证，Ⅰ和Ⅱ级1和2部分A-G组，仅在安全区域与威泰克WTC2106或MT2106仪表结合使用
FM认证，Ⅰ和Ⅱ级1和2部分A-G组，仅在安全区域与威泰克WTC2106或MT2106仪表结合使用
偏移测量：线性差动变换器测量
无检测板重量：61公斤
防尘：从检测板外壳开始*密封
DE20型冲板流量计是融合了几十年来从事动态称重的丰富经验而特殊设计的。专用于连续测量粉状，颗粒状等散状物料的瞬时流量及总累计量。广泛适用于化工，建材，冶金，电力，煤炭，烟草等行业生产工艺过程的控制。
DE20冲板流量计可以方便的安装在多种输送机的落料点下，包括螺旋给料机，振动给料机，皮带输送机，刮板输送机，风力输送系统或星形给料机上，所监测的典型物料包括：花费，水泥，焦炭，矿石，沙子，木屑，塑料颗粒，谷物，马铃薯片，大米以及糖果等物料。
工作原理：
冲板流量计的工作原理是将散状物料经导流，对连接在DE20传感器上的测量传感板冲击而形成的水平位移，传感器产生电压信号0—24伏，通过变送器360将电压信号转换成模拟信号，传送给积算器MT2106调节参数，同时积算处理并显示出瞬时流量和累计流量，使其更加精确。
特点：
① 环境温度可达-40℃~+60℃
② 量程从：0-80吨/每小时（DE10型号），61E+DE20型号：0-500T/H
③ 线性精度优于1%
④ 粉状、颗粒状及块状特料均可
⑤ 高度的可靠性和最少的保养作业
⑥ 无因附着而发生的零漂移
⑦ 体积小、重量轻、占空间小
（各工业部门均可采用）
DE20冲板流量计可以方便的安装在多种输送机的落料点下，包括螺旋给料机，振动给料机，皮带输送机，刮板输送机，风力输送系统或星形给料机上，所监测的典型物料包括：花费，水泥，焦炭，矿石，沙子，木屑，塑料颗粒，谷物，马铃薯片，大米以及糖果等物料。
工作原理：
冲板流量计的工作原理是将散状物料经导流，对连接在DE20传感器上的测量传感板冲击而形成的水平位移，传感器产生电压信号0—24伏，通过变送器360将电压信号转换成模拟信号，传送给积算器MT2106调节参数，同时积算处理并显示出瞬时流量和累计流量，使其更加精确。
特点：
① 环境温度可达-40℃~+60℃
② 量程从：0-80吨/每小时（DE10型号），61E+DE20型号：0-500T/H
③ 线性精度优于1%
④ 粉状、颗粒状及块状特料均可
⑤ 高度的可靠性和最少的保养作业
⑥ 无因附着而发生的零漂移
⑦ 体积小、重量轻、占空间小
（各工业部门均可采用）
8.食盐，水泥，煤粉，聚乙烯颗粒，工业大颗粒盐，等颗粒散状物料的测量。
The DE10 ram flowmeter can detect bulk material from 0.75 tons / h to 80 tons / h. The patented support system and waveform spring ensure that the detection plate is limited to horizontal direction. This displacement can be detected by a high-resolution sensor that outputs a voltage signal that is converted into a pulse frequency modulated digital signal free from noise.
Advantages
·'s unique design allows flowmeters to be installed in the worst working conditions
The · measurement is not affected by the impact point changes on the detection board
Material accumulation on the · test board does not affect the zero point
· has high reliability, low maintenance
The · is equipped with a mechanical damping system to absorb the shock or weaken the vibration
The · sensor is mounted in a housing, isolated from the material flow
· can also provide accurate measurements for pulsing or fluctuating material flow
Custom ram flow meter box
Xuzhou Wittaker can specially design boxes for customers to meet their special requirements. These boxes can be connected to the existing flange. In addition, they are easier to install, usually occupy a small space, and ensure the working performance of the ram flowmeter.
Specifications and parameters
Measurement range: 0-25 t / h ~0-800 t / h
Standard temperature: + 10℃ ~ + 80℃ (provides a lower or higher temperature configuration)
Material temperature: + 10℃ ~ + 80℃
Certification (optional): FM certification, and level 1 and 2 part A-G groups, used only in safe areas in conjunction with Wittec WTC2106 or MT2106 instruments
FM certification, and Level 1 and 2 part A-G groups, are used only in safe areas in conjunction with Wittec WTC2106 or MT2106 instruments
Offset measurement: a linear differential converter measurement
Weight of no board: 61 kg
Dust proof: fully sealed from the test plate housing
The DE20 ram flowmeter is specially designed with decades of experience in dynamic weighing. Dedicated for continuous measurement of instantaneous flow and aggregate accumulation of powder, granular scattered materials. It is widely used in chemical industry, building materials, metallurgy, electricity, coal, and tobacco industries.
DE20 ram flowmeter can be conveniently installed under the drop points of various conveyors, including spiral feeder, vibrating feeder, belt conveyor, scraper conveyor, wind conveyor system or star feeder, monitoring typical materials include: cost, cement, coke, ore, ore, sand, wood chips, plastic particles, grains, potato chips, rice and candy.
Operating principle:
The working principle of the ram flowmeter is to guide the scattered material through the flow to the DE20 sensor, generate a voltage signal 0-24 volts, convert the voltage signal into an analog signal through the transmitter 360 to the integrator MT2106 adjustment parameters, and display the instantaneous flow and accumulated flow to make it more accurate.
Features:
① ambient temperature up to-40℃ ~ + 60℃
The ② measuring range is from: 0-80 ton / hour (DE10 model), 61E + DE20 model: 0-500T/H
The ③ linear accuracy is better than 1%
④ powdery, granular and block special are available
⑤ high reliability and minimal maintenance work
The ⑥ has no zero drift due to the attachment
⑦ is small, light weight and small space
(Applfor by industrial sector)
8. Measurement of table salt, cement, powdered coal, polyethylene particles, industrial large grain salt, and other granular scattered materials.
Advantages
·'s unique design allows flowmeters to be installed in the worst working conditions
The · measurement is not affected by the impact point changes on the detection board
Material accumulation on the · test board does not affect the zero point
· has high reliability, low maintenance
The · is equipped with a mechanical damping system to absorb the shock or weaken the vibration
The · sensor is mounted in a housing, isolated from the material flow
· can also provide accurate measurements for pulsing or fluctuating material flow
Custom ram flow meter box
Xuzhou Wittaker can specially design boxes for customers to meet their special requirements. These boxes can be connected to the existing flange. In addition, they are easier to install, usually occupy a small space, and ensure the working performance of the ram flowmeter.
Specifications and parameters
Measurement range: 0-25 t / h ~0-800 t / h
Standard temperature: + 10℃ ~ + 80℃ (provides a lower or higher temperature configuration)
Material temperature: + 10℃ ~ + 80℃
Certification (optional): FM certification, and level 1 and 2 part A-G groups, used only in safe areas in conjunction with Wittec WTC2106 or MT2106 instruments
FM certification, and Level 1 and 2 part A-G groups, are used only in safe areas in conjunction with Wittec WTC2106 or MT2106 instruments
Offset measurement: a linear differential converter measurement
Weight of no board: 61 kg
Dust proof: fully sealed from the test plate housing
The DE20 ram flowmeter is specially designed with decades of experience in dynamic weighing. Dedicated for continuous measurement of instantaneous flow and aggregate accumulation of powder, granular scattered materials. It is widely used in chemical industry, building materials, metallurgy, electricity, coal, and tobacco industries.
DE20 ram flowmeter can be conveniently installed under the drop points of various conveyors, including spiral feeder, vibrating feeder, belt conveyor, scraper conveyor, wind conveyor system or star feeder, monitoring typical materials include: cost, cement, coke, ore, ore, sand, wood chips, plastic particles, grains, potato chips, rice and candy.
Operating principle:
The working principle of the ram flowmeter is to guide the scattered material through the flow to the DE20 sensor, generate a voltage signal 0-24 volts, convert the voltage signal into an analog signal through the transmitter 360 to the integrator MT2106 adjustment parameters, and display the instantaneous flow and accumulated flow to make it more accurate.
Features:
① ambient temperature up to-40℃ ~ + 60℃
The ② measuring range is from: 0-80 ton / hour (DE10 model), 61E + DE20 model: 0-500T/H
The ③ linear accuracy is better than 1%
④ powdery, granular and block special are available
⑤ high reliability and minimal maintenance work
The ⑥ has no zero drift due to the attachment
⑦ is small, light weight and small space
(Applfor by industrial sector)
8. Measurement of table salt, cement, powdered coal, polyethylene particles, industrial large grain salt, and other granular scattered materials.
