通信电缆 网络设备 无线通信 云计算|大数据 显示设备 存储设备 网络辅助设备 信号传输处理 多媒体设备 广播系统 智慧城市管理系统
杭州四海光纤网络有限公司
杭州四海光纤网络有限公司
ADSS/OPGW余缆架名称：余缆架光缆金具光缆热镀锌预留架杆用/塔用又名：预留架，放线架材质：Q235扁铁：a)50*5mmb)40*4mm用途：用于安放光缆接续时的富余光缆，一般设一个接头盒，都配一个余缆架
ADSS/OPGW余缆架
名称：余缆架 光缆金具 光缆热镀锌预留架 杆用/塔用
又名：预留架，放线架
材质：Q235 扁铁：a)50*5mmb) 40*4mm
用途：用于安放光缆接续时的富余光缆，一般设一个接头盒，都配一个余缆架。余缆架分杆用和塔用两种，如为杆用，则需要提供使用杆径。
产品详情
| 型号 | 固定部分长度L1（ mm） | 总长度（mm） | 重量（kg) | 备注 |
| PYLJ-1 | 400 | 1200 | 6 | 杆用 |
| PYLJ-2 | 400 | 1200 | 6 | 塔用 |
1.产品质量三包，对所有电力金具设备我公司均严格按照客户所提供图纸及技术要求（技术协议）并严格按照GB标准设计、生产和检验。
2.原材采购、设备设计、产品生产制造等过程中，严格按下列质量标准进行控制，确保每个工序处在质量受控状态，从而保证产品质量。
中华人民共和国电力行业标准（DL/T763-2001）“架空线路用预绞丝金具技术条件”。
中华人民共和国电力行业标准（DL/758-2001）“接续金具”
中华人民共和国电力行业标准（DL/759-2001）”连接金具”
3.所有出厂产品均严格按检验程序进行检验，保证产品一次交检合格率99%，成品抽查合格率99%。
4.对所有客户均提供：技术更新、质量更好、服务更佳的产品.
金具的订货除按设计部门提供的金具型号、数量外，由于光缆金具与光缆技术参数配合要求严格，也就是说两者要有很好的相容性，否则可能导致工程失败。通常金具与缆应作配合性试验后，才会有较高的可靠性。
ADSS / OPGW cable rack
Name: remaining cable rack, optical cable fittings, cable hot galvanizing, reserved rack pole / tower
Also known as: reserved rack, pay off rack
Material: Q235 flat iron: a) 50 * 5mmb) 40 * 4mm
Purpose: it is used to place the surplus optical cable when the optical cable is connected. Generally, it is equipped with a junction box and a surplus cable rack. There are two kinds of cable supports for poles and towers. If they are used for poles, the diameter of poles shall be provided.
product details
| model | Fixed part length L1（ mm） | Total length（mm） | weight（kg) | remarks |
| PYLJ-1 | 400 | 1200 | 6 | Pole |
| PYLJ-2 | 400 | 1200 | 6 | Tower |
1.Three guarantees of product quality. For all electric power fittings and equipment, our company designs, produces and tests in strict accordance with the drawings and technical requirements (technical agreement) provided by customers and in strict accordance with GB standards.
2. In the process of original procurement, equipment design and product manufacturing, the following quality standards shall be strictly followed to ensure that each process is under quality control, so as to ensure the product quality.
Electric power industry standard of the people's Republic of China (DL / t763-2001) "technical conditions of preformed wire fittings for overhead lines".
Electric power industry standard of the people's Republic of China (DL / 758-2001) "connecting fittings"
Power industry standard of the people's Republic of China (DL / 759-2001) "connecting fittings"
3. All ex factory products shall be inspected in strict accordance with the inspection procedures to ensure that the qualified rate of one-time inspection of products is 99%, and that of finished products is 99%.
4. Provide all customers with products with updated technology, better quality and better service
In addition to the model and quantity of fittings provided by the design department, the hardware fittings of optical cable and the technical parameters of optical cable shall be strictly matched, that is to say, they shall have good compatibility, otherwise the project may fail. Generally, the fitting and cable should be tested for compatibility before they have higher reliability.
您感兴趣的产品PRODUCTS YOU ARE INTERESTED IN
智慧城市网 设计制作，未经允许翻录必究 .
请输入账号
请输入密码
请输验证码
