塑料水平垂直阻燃试验机适用范围
用于测试塑料类及非金属材料类物质燃烧性能的试验仪器。适用于塑料和非金属材料试样处于50W火焰条件下，水平或垂直方向燃烧性能的试验室测定方法。(实物如右图)
- 微电脑控制操作
- 自动化程度高：自动记录试验时间并可保存，自动显试结果，自动计时，自动点火，自动报警系统，施焰结束后本生灯自动退回
- 水平、垂直燃烧试样夹电机控制
- 记时准确
三、相关技术参数
①仪器合适工作条件及主要技术指标
- 环境温度：室温～40℃； 相对湿度：≤75％；
- 供电电压和功率：220V±10％ 50HZ 功率150W
- 本生灯自动点火时间：任意设定
- 本生灯内径9.5mm±0.5mm
- 气源：液化石油气（仲裁时加工业甲烷气）；
- 304全不锈钢箱体耐高温高湿高腐蚀环境
- 燃烧箱内部容积：0.75立方米（不锈钢款）
- 仪器重量约：100kg
- 工作电源 ： 220V AC 50HZ
- 计时范围：0~999s 记时精度：10s±0.2s 30s±0.2s；
- 施焰时间 ： 0～999.9S（可调）
- 余焰时间 ： 0～999.9S（可调）
- 余灼时间 ： 0～999.9S（可调）
- 燃烧角度 ： 0°、20°、45°可选择
- 火焰高度 ： 20mm ~ 175mm 可调
- 火焰温度：（100-1000）℃可调
- 气体流量 ： 0.03~ 0.3ml/Min
- 燃 烧 灯 ： 灯管内径9.5±0.3mm,长度：100mm±10mm
- 时间装置 ： 能精确到0．5S
- 位置调节 ： 样品夹支架可上下、左右调节，燃烧座可前后调节，调节行程均大
- 设备外形尺寸：0.75立方不锈钢款箱体 长*款*高1300*650*1200
②设计标准：
GB-T2408-2008《塑料燃烧性能的测试-水平法和垂直法》（ANSI/UL94 -2006）
③符合标准：
GB-T5455 《 纺织品 燃烧性能试验 垂直法》
GB-T13488《橡胶燃烧性能测定—垂直燃烧法》
GB/T5169.16-2002
ANSI/UL94
IEC60950-1、
IEC695-2-2
四、产品配置
- 设备主机 壹台
- 电源线 壹根
- 滴落盘 壹只
- 点火器 壹只
- 螺丝刀 壹只
- 紧箍 贰个
- 气源管 壹点伍米
- 备用标尺 壹把
- 说明书 壹份
- 合格证 壹张
Product Name: Horizontal and vertical burning tester
Product Model:CZF-5
Design Standards ：GB/T2408-2008 Plastics. Determination of burning characteristics. Horizontal and vertical test
Brief Introduction :That horizontal and vertical burning tester is designed according to the chinese national standard《 GB/T2408-2008 Plastics. Determination of burning characteristics. Horizontal and vertical test》ａnd meet the requirements of it compley。Both the horizontal and vertical burning test can be completed in this machine。The test data can be recorded and saved automatically。It is also suitable for the chinese national standard《 GB/T 5455 Textiles. Burning behaviour. Vertical method 》.And unlike the CZF-3 tester ,it,s more sophisticated and more automated。 The burning body is 0.5m3ａnd that is larger than the CZF-3 tester。By the way， 0.5m3 is in accordance with UL94-2006 and GB-T2408-2008。
Design standard of the horizontal and vertical burning tester ：
GB-T2408-2008《 Plastics. Determination of burning characteristics. Horizontal and vertical test》
The standard can be meet: UL94-2006、GB-T 5455 、 GB-T13488 、GB-T5169、 IEC60695-11-3、IEC60695-11-4、IEC60950-1、IEC695-2-2
（一）The environmental requirements
1. Requirements about environmental temperature : -10℃～30℃
2. Relative humidity:≤85％
3. Supply voltage and power:220V±10％ , 50HZ 150W
(二)Characteristic
- The diameter of the burner is 9.5mm+0.3mm，The diameter ofthe Bunsen burner is 9.5mm±0.5mm
- There is a screw nut on the bunsen burner used to control the height of blue flame
- The auto-ignition time of the bunsen burner can be set up arbitrarily
- it，s tilt angle is between 0° and45°，EachInterval can be tilted 5 degrees automatically
- You can djust the flame height between 20mm + 2mm and 100mm + 10mm
- The bunsen burner move to the bottom of the test sample quickly through the motor
- The bunsen burner return automatically when the flame application completed
- The flame applying time of the bunsen burner is between0～999.9S+0.1s and it can set up automatically within that band。the flame can set up between 20 and 175mm
- The afterflame time can set up between 0 to 999.9S+0.1s and the tester will keep the minutes automatically ，in addition，you can pause it manually
- The residual burning time can set up between 0 and 999.9S+0.1s and the tester will keep the minutes automatically ，in addition，you can pause it manually
- The source can sue 98% methane、 natural gas、 liquefied petroleum gas or coal gas
- Flux of the methane can set up between 105ml/min and1000ml/min。
- A electronic switch is set on the gas pipeline
- You should close the The gas switch on the panel when the test is finish，around this time， the bunsen burnerwill in time go out of itself
- The burning body is 0.5m3ａnd it has a black background ，the background illumination must be 20Lux or less 。Moreover， we also have 0.75m3 burning body if it is in need
the upper and lower left and right travel of the sample frame must be 300mm or more 。There is a servo motor cotrol the horizontal and vertical distance from test sample and the flame
- The flue gas will be discharged by the ventilating fan who is on the experimental box top when the test finish
- The whole test process is automatically controlled and the ventilation system is independent
