通信电缆 网络设备 无线通信 云计算|大数据 显示设备 存储设备 网络辅助设备 信号传输处理 多媒体设备 广播系统 智慧城市管理系统
营派阀门（上海）有限公司
营派阀门（上海）有限公司
进口潜水排污泵Germany Kaysen
主要应用：
●医院、宾馆的污水排放
●市政工程、建筑工地
●城市污水处理厂排水系统
●勘探、矿山配套附机
●人防系统排水站、自来水厂的给水装置
●农村、沼气池、农田灌溉
●住宅区的污水排水
●工厂、商业严重污染废水的排放
德国KAYSEN凯森泵业有限公司
Germany Kaysen Pump Co., Ltd.
凯森泵业总代理：营派阀门（上海）有限公司
详细资料请登录：营派阀门（上海）有限公司
进口潜水排污泵Germany Kaysen
德国KAYSEN凯森进口潜水排污泵概述
潜水式排污泵采用大流道抗堵塞水力部件设计，大大提高污物通过能力，能有效地通过泵口径的5倍纤维物质和直径为泵口径约50%的固体颗粒。设计合理，配套电机合理，效率高，节能*。潜水式排污泵机械密封采用双道串联密封，材质为硬质耐磨碳化钨，具有耐用、耐磨等特点，可以使泵安全连续运行800小时以上。泵油室内设有油水探头，当水泵侧机械密封损坏后，水进入油室，探头发生信号，对泵实施保护。可根据用户需要配备全自动安全保护控制柜，对泵的漏水，漏电，过载及超温等进行监控，保证泵运行可靠安全。双导轨自动耦合安装系统，给泵的安装的安装，维修带来了*的方便，人可不必为此而进出污水坑。浮球开关可根据所需的水位变化。自动控制泵的停启，无需专人看管。电机运行不过载。根据使用场合电机可采用水套式外第三者循环冷却系统，能保证电泵在无水（干式）状态下安全运行。安装方式有固定式自动耦合安装和移动式自由安装二种，可满足不同的使用场合。
KAYSEN潜水排污泵图片展示：
潜水泵日常维护
日常维护潜水泵每天检查电源线。禁止漏水潜水泵运行。每天检查泵体是否损坏，确保电机在工作时不漏气。手术后，应及时清理附在泵上的碎屑，泵清洗。为确保潜水泵正常运行，您必须遵守这些要求。潜水泵使用前，应用兆欧表检查电机的绝缘电阻，zui小值不得低于50M。灌水马达应打开塞子，注满清水，然后拧紧塞子，不要把灌溉塞子直接拧进井里。使用前检查电缆是否有裂纹，以防破裂。如果损坏应该交换，以防止泄漏。潜水泵在进入水中之前应先怠速1-2分钟，启动两次，检查是否正常起动和怠速，转向满足要求。如果转向，而不是交换任何两相接线。检查杨管是否有裂纹，联轴器是否安全。潜水井下井和提升，绝不允许电缆本身，以避免损坏电缆或断开接头，造成不应有的事件。应该用电线或卡板和提升。电源电压应控制在额定电压的±5％范围内，这样电机才能正常工作。如果电压过低或过高，电动机不能继续使用，以免在工作过程中*损坏电机的过电压或欠压。立式潜水泵应浸入水中，不能倾斜。移到水下5米的水深是适当的。高含沙量的潜水泵不得输送水或泥浆。实际水头潜水电泵应在额定电梯的0.8-1.1倍范围内使用，以提高机组效率，节约能源，同时避免电机过载。潜水电动机的接线必须接入现实，避免燃烧电动机运行电动机相。电缆必须经常检查是否有裂纹，划痕等，有及时的更换或修理。如发现机油漏油，应及时向生产厂家进行维修或保养，更换密封件。电动机应定期清洗浸水沉砂池，更换电机内腔水。潜水泵运行六个月后，应进行维护检查，更换损坏的部件。使用潜水泵后，水马达应在马达内部放入净水，将泵抽干净，油锈，并保持直立在干燥的地方。
Submersible Pumps Routine Maintenance
Submersible Pumps Routine Maintenance Check the power cord every day. The absolute prohibition of leakage water submersible pump operation. Checked daily pump body for damage, ensure that the motor does not leak at work. After the operation, you should promptly clean up the debris attached to the pump, the pump rinse. To ensure the normal operation of submersible pump, you must follow these requirements. Submersible pump before use, shall be checked with a megger insulation resistance of the motor, the value of the minimum of not less than 50M. The flooding irrigation motor should open the plug, filled with clean water and then tighten the plug, do not wring out the irrigation plug directly into the well. Check the cable for cracks before use, to break. If damage should be swapped to prevent leakage. Submersible pump should be before launching into the water, then idle for 1-2 minutes and start twice to check whether the normal starting and idling, turn to meet the requirements. If the steering Instead, you can swap any two-phase wiring. Check whether there are cracks Yang pipes, couplings are secure. submersable well pump to go down and lifting, never allow the cable itself, to avoid damage to the cable or disconnect joints, causing undue incidents. Should go down with wire or card board and lifting. Supply voltage should be controlled at the rated voltage of ± 5% range, so the motor to work properly. If the voltage is too low or too high, the motor can not continue to use, in order to avoid long-term motor overvoltage or undervoltage at work when damaged. Vertical submersible pump should be dipping into the water, not diagonal. Moving into the water depth of 5 meters under the water level is appropriate. Submersible pump high sand content shall not transport water or mud. Actual head submersible pump should be used within 0.8- 1.1 times the rated lift in order to improve unit efficiency, energy conservation, while avoiding motor overload. submersible electric motor wiring must be connected to reality, to avoid burning motor running motor phase. The cable must always check whether the cracks, scratches, etc., there is the timely replacement or repair. If motor oil leakage, it is timely to the manufacturer for repair or maintenance, replacement sealing element. Electric motor should be cleaned regularly flooding grit chamber, replace the motor cavity water. Submersible pump running after six months, should maintenance checks, replace the damaged parts. After using submersible pumps, water motor should put a net water inside the motor will pump clean, oiled rust and keep it upright in a dry place.
进口潜水排污泵Germany Kaysen
位于德国SchwäbischGmünd的凯森Kaysen泵业有限公司是亚欧的各种流体水泵和隔膜泵制造商之一。60多年来，凯森以“德国制造”的可靠性和质量达到了zui高标准。凭借我们全面的产品组合，我们支持亚欧各地的客户成功掌握供水，采矿，工业，化工，造纸，电力，食品，制药，污水和海上行业的苛刻抽水任务。作为上述领域创新技术的供应商，我们是液体需要安全，高效和经济运输的*合作伙伴。
德国凯森始终坚持“重质量，讲信誉”为宗旨。产品现全国各地，并已逐步开发海外市场。公司多次被评为“重合同讲信用”企业，深得用户的信赖和广泛的赞誉。
The Kaysen Pumps GmbH in SchwäbischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.
您感兴趣的产品PRODUCTS YOU ARE INTERESTED IN
智慧城市网 设计制作，未经允许翻录必究 .
请输入账号
请输入密码
请输验证码
