溜槽堵塞检测器 GA-29000-GYLC-1适用于检测胶带输送机运输系统中的溜槽堵塞故障。当溜槽内形成堵塞时，检测器将发生报警、振动或停机信号，防止由物料堵塞溜槽而造成的恶性事故。

溜槽堵塞检测器 GA-29000-GYLC-1

图片

安装与接线

（一）安装方法：

1、在溜槽侧壁一适当位置开240×260长方口，然后在开口上方约100~200mm处，溜槽内壁焊接一块长300mm左右的挡板，以防大块物料落下直接冲击活动门发生误动作。再用随机所配橡胶板将开口*覆盖、封闭。

1、将本装置用M10×25螺栓紧固在弯角件上即可。

（二）安装要领及主要事项

1、本系列保护装置可两个为一组，安装于溜槽相对的并且不受物料冲击的两个侧壁上，度根据用户需要而定。一般安装在溜槽底部向上三分之二度为宜。

2、本系列产品装置也可用四个分两组使用，一组安装在溜槽侧壁从底算起三分之一相对度，作为轻度堵塞检测。用于接振打装置信号，当溜槽发生堵塞时，振打装置接收到信号后，便开始振打；另一组安装底部三分之二处，作为重度堵塞时输出停机信号。

（三）接线：由保护装置引出一条4芯电缆线

维护和使用

此装置使用半年以后，要进行一次维护检查，检查紧固螺钉是否有松动、脱落现象，待拧紧后，再进行使用。同时要在门轴的轴套里涂以润滑油，并清除积尘。

使用条件

1、海拔度低于2000m

2、环境温度：-35℃~+50℃

3、相对湿度：不大于95％

4、大气压力：80~110Kpa

5、工作位置：安装在溜槽不受物料冲击的侧壁上

主要用途

适用于检测胶带输送机运输系统中的溜槽堵塞故障。当溜槽内形成堵塞时，检测器将发生报警、振动或停机信号，防止由物料堵塞溜槽而造成的恶性事故。

可引起输送物料的堆积或输送机皮带的损坏以及火灾发生，使用溜槽堵塞开关可预防此事故的发生。溜槽堵塞开关在安全运行输送系统里是*的保护装置，广泛应用钢铁厂、火力发电厂、水泥厂、化工厂、港口等等。溜槽堵塞开关由摆动形检测板和限位开关组成，安装在溜槽侧壁已开好的长方形开口处，当溜槽被输送物料堵塞时，检测板将向外倾斜，此时限位开关发生动作。当故障排除后，检测板在弹簧作用下自动复位。

The chute blockage detector ga-29000-gylc-1 is suitable for detecting the failure of chute in the conveyor system of belt conveyor. When there is a blockage in the chute, the detector will have alarm, vibration or stop signal to prevent the bad accident caused by the material blocking chute.
Chute block detector ga-29000-gylc-1 pri.
Chute block detector ga-29000-gylc-1 picture.
Installation and wiring
(I) installation method:
1, in the 240 x 260 rectangular chute wall a proper pla to open the mouth, then about 100 ~ 200 mm above the mouth, chute wall welding a pie of about 300 mm long, in case of large materials directly impact activity occurs mperation. The opening is compley covered and closed with a random rubber sheet.
1. Use the M10 x 25 bolt to fasten the devi on the corner pie.
(2) installation essentials and main items.
1. This series of protection devis can be set in two groups, which are installed in the two side walls of the chute relative to the material and are not affected by the material impact. The height is determined according to the user's needs. Generally installed at the bottom of the chute upward two-thirds height is appropriate.
2. This series of product devis can also be used in two groups. One group is mounted on the side wall of the chute and one third of the relative height is taken from the bottom, which is used as a light plugging test. Used for reiving the signal of the percussion devi, when the chute is blocked, the vibration devi reives the signal and starts to strike. The other set is installed at two thirds of the bottom, which is the output stop signal when it is heavily blocked.
(3) wiring: a 4-core cable is drawn from the protective devi.
Maintenan and use
After the devi is used for six months, it is nessary to conduct a maintenan check to check whether the fastening screws are loose or falling off, and then use them after tightening. Also apply lubricating oil to the axle sleeve of the door shaft and remove dust.
Conditions of use
1. The altitude is less than 2000m.
2, the environment temperature: - 35 ℃ ~ + 50 ℃
3. Relative humidity: no more than 95%.
4. Atmospheric pressure: 80~110Kpa.
5. Position: installed on the side wall of the chute that is not impacted by the material.
The main purpose
The chute blockage detector ga-29000-gylc-1 is suitable for detecting the failure of chute in the conveyor system of belt conveyor. When there is a blockage in the chute, the detector will have alarm, vibration or stop signal to prevent the bad accident caused by the material blocking chute.
The chute clogging detector ga-29000-gylc-1 can cause the accumulation of conveying materials or the damage of conveyor belt and the occurren of fire. The use of the chute plug switch can prevent the occurren of this accident. The chute blocking switch is an indispensable protection devi in the safe operation conveying system. It is widely used in steel plants, thermal power plants, ment plants, chemical plants, ports and so on. Chute blocking switch is composed of oscillating shape measuring plate and the limit switch, mounted on the chute wall has good rectangular openings, when conveying material chute was blocked, detection board will tilt outwards, limit switch happen at this time. When the fault is removed, the test plate is automatically reset under the action of spring.