进入公司商铺
Electric welding machine cable product description:
本产品适用于对地电压交流不超过200V和脉动直流峰值400V电焊机用二次侧接线及连接电焊钳.是适用于电焊机二次侧接线及连接电焊钳的电缆,额定电压交流不超过200V和脉动直流峰值400V。结构为单线芯,采用多股软导线复绞制成。导电线芯外面采用耐热聚酯薄膜绝缘带绕包,zui外层用橡皮制成的绝缘兼护套做为保护层。YH电焊机电缆
This product is suitable for AC voltage not exceeding 200V and 400V peak pulse current welding two side connecting line and electrode holder. Is applicable to the welding machine wiring two side and special cable connection welder, AC rated voltage not exceeding 200V and 400V peak pulse current. For a single core structure, a multi unit made of soft wire cutter. Conductive wire core outside the use of heat-resistant polyester film insulation tape wrapped around, the outermost layer made of rubber insulation and sheath as protective layer.YH电焊机电缆
表6-9-14电焊机电缆型号
Table 6-9-14 welding machine cable model，
型号 名称
Type name
YH 天然胶护套电焊机电缆
YH natural rubber sheath welder cable
YHF 氯丁或其它相当的合成胶弹性体护套电焊机电缆
YHF neoprene or other equivalent synthetic elastomer sheath electric welding cable
的使用要求：
Use requirements of YH electric welding machine cable:
(1)YH电缆是在低电压(zui高电压为200V)大电流的条件下工作,要求具有一定耐性。
(1) YH cable is working at low voltage (maximum voltage of 200V) under high current conditions, requiring a certain degree of tolerance.
(2)焊把线电缆*允许工作温度不应超过65℃。
(2) long allowed working temperature of welding wire cable shall not exceed 65 DEG C.
(3)电机引接线电缆频繁地移动，扭绕和施放,要求柔软,弯曲性能好。
(3) motor wiring cables frequently move, twist around and cast, requiring soft, good bending performance.
(4)在施放中易受到尖锐钢铁构件的刮、擦,故要求电缆绝缘抗撕、耐磨等机械性能好。
(4) in the casting vulnerable to sharp steel components scraping, cleaning, so the cable insulation tear, wear and other mechanical properties are good.
(5)使用环境条件复杂,如日晒、水沸、接触泥水、机油、酸碱液体等,要求有一定的耐气候性和耐油、耐溶剂性。
(5) the use of complex environmental conditions, such as sun, water boil, contact mud water, oil, acid and alkali liquid, require a certain weather resistance and oil resistance, solvent resistance.
(6)有时会碰到热焊件,要求耐热变形性好。
(6) sometimes encountered hot weldment, requiring good thermal deformation.
(7)经常移动,要求外径小,重量轻。由于对此种电缆电性能要求不高,且使用环境条件复杂,在结构上要求满足各种复杂的环境因素是不适宜的。使用时注意改善使用条件,防止外来破坏。
(7) frequent movement requiring small external diameter and light weight. Because of the low demand for the electrical performance of the cable and the complicated use of the environment, it is not suitable to meet various complicated environmental factors in the structure. When used to improve the use of conditions to prevent foreign damage.
电焊机电缆[1]（YH电缆）全称高强度橡套电焊机电缆，俗称焊把线，是YC电缆（通用橡套电缆）的一种。用于电焊机二次侧接线及连接电焊钳、电焊机的电缆，其特性是电阻大、电压低。工作电压一般为450V到750V。
Electric welding machine cable [1] (YH cable) full of high strength rubber sleeve electric welding cable, commonly known as welding wire, is a YC cable (general rubber cable). For the electric welding machine two secondary side wiring and electrode holder, welding connection cable, its characteristic is high, low voltage resistance. Operating voltage is generally 450V to 750V.
电焊机电缆的结构为单线芯，一般为多跟铜丝组成铜丝组，多组铜丝组则组成电焊机电缆的导体部分，所以YH电缆线体较粗，铜丝数百根。多组铜丝的周围被一层耐热聚酯薄膜绝缘包裹。绝缘层一般为*橡胶，铜丝为无氧铜，这样，才能保证线芯的良好导电性及电缆的安全性。
The structure of electric welding machine cable for a single core, usually with copper wire conductor composed of groups, groups of copper group is composed of welding cable, so YH cable body coarse copper wire, hundreds of root. Many groups around the copper wire by a layer of heat-resistant polyester film wrapped insulation. The insulating layer is pure natural rubber, copper wire for copper, so, in order to ensure the safety of wire and cable of good conductivity.
常用电焊机电缆的规格型号有16平方、25平方、35平方、50平方、70平方、95平方、120平方等。
Commonly used electric welding cable specification model has 16 square, 25 square, square, 50 square, 35 square, 70 square, square, 120 square.
电焊机电缆的几个特性：
Several characteristics of electric welding machine cable:
(1)YH电缆是在低电压(zui高电压为200V)大电流的条件下工作,要求具有一定耐性。
(1) YH cable is working at low voltage (maximum voltage of 200V) under high current conditions, requiring a certain degree of tolerance.
(2)焊把线电缆*允许工作温度不应超过65℃。
(2) long allowed working temperature of welding wire cable shall not exceed 65 DEG C.
(3)电机引接线电缆频繁地移动，扭绕和施放,要求柔软,弯曲性能好。
(3) motor wiring cables frequently move, twist around and cast, requiring soft, good bending performance.
(4)在施放中易受到尖锐钢铁构件的刮、擦,故要求电缆绝缘抗撕、耐磨等机械性能好。
(4) in the casting vulnerable to sharp steel components scraping, cleaning, so the cable insulation tear, wear and other mechanical properties are good.
(5)使用环境条件复杂,如日晒、水沸、接触泥水、机油、酸碱液体等,要求有一定的耐气候性和耐油、耐溶剂性。
(5) the use of complex environmental conditions, such as sun, water boil, contact mud water, oil, acid and alkali liquid, require a certain weather resistance and oil resistance, solvent resistance.
(6)有时会碰到热焊件,要求耐热变形性好。
(6) sometimes encountered hot weldment, requiring good thermal deformation.
(7)经常移动,要求外径小,重量轻。由于对此种电缆电性能要求不高,且使用环境条件复杂,在结构上要求满足各种复杂的环境因素是不适宜的。使用时注意改善使用条件,防止外来破坏。
(7) frequent movement requiring small external diameter and light weight. Because of the low demand for the electrical performance of the cable and the complicated use of the environment, it is not suitable to meet various complicated environmental factors in the structure. When used to improve the use of conditions to prevent foreign damage.
电焊机电缆使用与维修
Electric welding machine cable use and maintenance
1、本装置为不可维修型，其各项保护特性由制造厂规定，不可随意调整。如有异常与本公司；
1, the device is not maintenance type, its protection characteristics by the manufacturer, not optional adjustment. If abnormal contact with the company;
2、弧焊机有风冷及主回路有接触器的，要将风机及接触器线圈电源接于装置的输入电源端；
2, arc welding machine has air cooling and the main circuit contactor, the fan and contactor coil power supply connected to the device input power supply end;
3、每次使用前观察保护器指示灯状态，红灯是电源指示，绿灯是安全电压指示，其正常状态
3, before each use to observe the protector indicator state, red light is power indication, green light is safe voltage indication, its normal state
