钢板止水带360x10规格@齐齐哈尔
在箱型基础或地下室，底板和外墙板的混凝土是分开浇捣的，下次再浇捣墙板混凝土时，就有一条施工缝，当这条缝的位置在地下水位线以下时，就容易产生渗水。这样就需要对这条缝进行技术处理，处理的方法很多，其中比较通行的方法是设置止水钢板如图。
Or the basement, in the box foundation slab and the slab concrete is cast separay, cast again next time wallboard, there is a construction joint, when the seam position is below the underground water level, is prone to water penetration. So you need to the seam technology processing, processing a lot of methods, one of the very popular method is to set up water stop plate as shown in figure.
而就在箱型基础或地下室，底板和外墙板的混凝土是分开浇捣的，下次再浇捣墙板混凝土时，就有一条施工缝，当这条缝的位置在地下水位线以下时，就容易产生渗水。这样就需要对这条缝进行技术处理，处理的方法很多，其中比较通行的方法是设置止水钢板。即在浇筑下层混凝土时，预埋300*3的钢板，其中有10-15cm的上部露在外面，在下次再浇筑混凝土时把这部分的钢板一起浇筑进去，起到阻止外面的压力水渗入的作用。一般钢板止水带是采用冷轧板作为母材,因为冷板厚度能够均匀，热板一般厚度达不到均匀的程度，厚度一般为2毫米或者3毫米，长度一般加工成3米长或者6米长，一般为三米好运输。止水钢板对焊接节点要求较高，不能出现漏点，影响防水性能。
Or the basement, and on the box foundation slab and the slab concrete is cast separay, when concrete is poured again next time wallboard concrete, there is a construction joint, when the seam position is below the underground water level, is prone to water penetration. So you need to the seam technology processing, processing a lot of methods, one of the very popular method is to set up water stop plate. Namely when casting lower concrete, embedded 300 * 3 steel plate, there are 10 to 15 cm exposed, the upper part of the next time when the concrete casting in this part of the plate together, have the effect of prevent outside the pressure of water infiltration. Manufacture steel plate water stop is commonly used as the parent metal, because of the cold plate thickness is uniform and the degree of thickness of hot plate generally not uniform, the thickness of 2 mm or 3 mm, length is generally processed into 3 meters or 6 meters long, usually for three meters. Check the demand is higher, shuicheng steel slabs welding node cannot be funnelled, affect the waterproof properties.
1、应尽力保证止水钢板在墙体中线上；
2、两块钢板之间的焊接要饱满且为双面焊 ，钢板搭接不小于20mm；
3、墙体转角处的处理，一、整块钢板弯折；二、丁字型焊接；三、7字型焊接。
4、止水钢板的支撑焊接，可以用小钢筋电焊在主筋上；
5、止水钢板穿过柱箍筋时，可以将所穿过的箍筋断开，制作成开口箍，电焊在钢板上。
6、止水钢板的“开口”朝迎水面。
1, should try our best to assure the centerline of the steel plate water stop in the wall;
2, between two pieces of steel plate welded to the full and the double-sided welding, steel plate lap should not less than 20 mm;
3, the processing of wall corner, one, the whole steel plate bending; Second, the t type welding; Three, seven type welding.
4, support welding of the steel plate water stop, can use small steel welded on the main reinforcement;
5, water stop plate through the column stirrup, can be through the stirrup disconnect, made into open collar, electric welding on the steel plate.
6, water stop plate "open" toward the face of the water.
