6254-FN聚酰亚胺薄膜F46胶带
一、产品简介：
6254-FN聚酰亚胺薄膜F46胶带是由6051-FN型聚酰亚胺薄膜单面或双面涂以F46胶经干燥分切而成的胶带（以下简称胶带）。该胶带使用于做电工导线绕包绝缘材料，在350℃—380℃温度下0.5min 熔融成型。执行标准：KAPTON*FN型绝缘膜。
二、技术参数：
1.外观：胶带应干爽、平整、无气泡、无杂质
2.尺寸：
1）长度：胶带长度及接头数根据用户要求，满足其需要。
2）宽度：胶带的宽度及允许偏差为10mm±0.5mm、15mm±0.5mm。根据用户需求可提供其他宽度规格的胶带。
3）胶带的标称厚度及允许偏差应符合下表规定
Kapton*FN 规格 | 120FN 616B | 150FN019 | 200FN919 |
TY6254—FN 规格 | 0.033mm双面 | 0.038mm单面 | 0.05mm双面 |
标称厚度 mm | 0.033 | 0.038 | 0.05 |
允许偏差 mm | +0.003
-0.003 | +0.004
-0.004 | +0.006
-0.004 |
3.性能要求：
项目名称 | 性能指标 |
厚度（mm） | 0.033双面 | 0.038单面 | 0.05双面 |
纵向伸长率 % | ≥55 | ≥55 | ≥55 |
介电强度 KV/mm | ≥197 | ≥157 | ≥130 |
剥离强度 | | | |
N/10ｍｍ | | | |
胶面—胶面 | ≥2.3 | 不合适 | ≥3.5 |
胶面—底材 | 不合适 | ≥2.3 | 不合适 |
胶面—铜材 | ≥2.3 | ≥2.9 | ≥3.5 |
包装、标志、贮存和运输：
1、胶带卷、盘应卷在塑料或纸管芯上，然后装在塑料袋内，封好袋口再装入内衬访潮纸的木箱或干燥洁净的纸箱内。
2、每一包装中应附有产品的检验合格证，箱体上标明产品名称、规格批号、毛重、净重、生产日期、生产厂名称，及“防潮”“防冲击”等字样。
3、该产品从生产之日起贮存期为六个月。超过贮存期按本标准进行检验，合格者仍可使用。
4、胶带应贮存在避光、干燥、洁净、通风良好的库房中。
5、胶带运输时，应避光、防潮、不得重压、摔打和机械损伤。
6254-FN聚酰亚胺薄膜F46胶带
6254-FN Polyimide Film Adhesive Tape F46
Executive Standard: KAPTON*FN insulating film
Standard No: TY6254-FN
Applicable Range: This product is manufactured with the raw material of polyimide film painted with F46 adhesive on single or both sides. After drying, it has been cut into different width. The product can be used for electrical lead winding insulating material. This product is fused at the temperature from 350℃ to 380℃ at 0.5 minute.
1.Technological requirement:
1.1 Appearance:
The tape should be dry, clean and smooth and the tape should have no defects such as air bubble, pinhole, elc.
1.2 Dimension:
1)Length: The length of the tape as well as the number of splice should be made as the requests of client.
2)Width: the width of the tape and its tolerance is as follows: 10mm±0.5mm, 15±0.5mm other width of tape is available too.
3)The tape’s standard thickness and its tolerance is as follows:
Kapton FN Spe | 120FN 616B | 150FN019 | 200FN919 |
TY6254-FN Spec | 0.033mm double sides | 0.038mm single side | 0.05mm double sides |
Standard thickness mm | 0.033 | 0.038 | 0.05 |
Tolerance mm | +0.003
-0.003 | +0.004
-0.004 | +0.006
-0.004 |
1.3.Performance:
Item | Index |
KAPTON * Type | 120 FN616B | 150FN019 | 200FN919 |
Thickness（mm） | 0.033 double sides | 0.038 single side | 0.05 double sides |
Elongation % | ≥55 | ≥55 | ≥55 |
Dielectric strength KV/mm | ≥197 | ≥157 | ≥130 |
peeling strength
N/10ｍｍ
adhesive—adhesive
adhesive—tape
adhesive—copper | ≥2.3
N/A
≥2.3 | N/A
≥2.3
≥2.9 | ≥3.5
N/A
≥3.5 |
2.Packing, marking, storage and transportation
2.1 The film, tape should be rolled on the plastic or paper core. Put it into a plastic bag. After sealing the bag, put them into a wooden or dry paper box. with desiccant in it.
2.2 The test report should be put into the box. Each box should have product’s name, specification, batch number, gross weight, net weight, production date, manufacturer, dampproof as well as impact-proof on it.
2.3 The shelf life is 6 months. It still can be used if the quality is ok after inspection.
2.4 The product should be stored in a lightproof, dry, clean, and ventilated warehouse.
2.5 On transportation, the product should avoid sun light, humidity. The product should not be stressed, breaked and avoid mechanical manage.
