EBBS-60A两级跑偏开关,跑偏传感器广泛用于冶金、煤炭、水泥建材、采矿、电力、港埠、冶金、化工等领域的各种带式输送设备。
EBBS-60A两级跑偏开关厂家
EBBS-60A两级跑偏开关服务
应用范围
常规皮带输送机，包括平皮带输送机和槽形皮带输送机
地下、索道支撑皮带输送机
轮船装卸系统、堆取料输送机
技术参数
工作电压：24VDC
接点容量：2个SPDT 400VAC 10A
一级报警：20° 二级报警：35°
侧面滚轮倾斜角度：≤75°
防护等级：IP67
环境温度：-20℃～+80℃
电缆入口：4*M20*1.5
电缆规格：6~12mm
产品特点
具有地址编码，内置RS485总线收发器
通讯波特率可编码
的ModBus-RTU通讯协议
机械触点，没有误动作
坚固的铸铝外壳、静电防腐涂装适应于恶劣工矿环境安装
防护IP67在恶劣环境也可使用;使用性能的微动开关和无需维护的滚珠轴承，耐久性
动作杆轴承额定转速5000转⁄分，适用皮带速度6.35米⁄秒
侧面滚轮zui大倾斜角度75度，因此输送带发生异常偏离时保护开关也会准确动作
EBBS-60A两级跑偏开关,跑偏传感器适用于皮带输送机，能使皮带输送机在皮带跑偏将导致严重挂边磨损甚至发生撕裂事故前就发出报警信号以及进一步的自动停车。
能及时有效的保护设备安全、避免事故扩大化，达到保障、保护设备的目的。另外由于信号可发送至控制系统，方便实现工厂自动化控制，因此又可达到减员增效，集中控制，利于与调度的目的。
注意事项
1、跑偏开关档轮与皮带保持垂直。
2、建议跑偏开关挡轮与皮带边缘距离保持120-160mm。
3、跑偏开关底座固定牢固。
订货须知
1、 选配件：安装支架。
安装说明
1、两级跑偏开关底座两边各有Ф12mm孔，在皮带机旁角铁架钻Ф12mm孔，用M10×30mm螺丝紧固跑偏开关。
2、安装跑偏开关应选择输送装置易出现跑偏的位置处安装，参考应用单位工艺要求，同时要考虑皮带与挡轮的有效间距和推力，建议皮带与档轮间的安装距离为120-160mm。
3、安装距离：建议每50米安装一对跑偏开关。
4、跑偏开关出厂时配有长度0.5米四芯橡套电缆，芯线上配有1、2、3、4线号，其中1、2为常开接点是一级报警信号，3、4为常闭接点是二级停机信号。
广泛应用于机械、机床制造业及食品厂、纺织、造纸、轻工、化工、矿山、冶金、航空工业、电力保安、汽车工业、船舶交通运输、建筑、地铁等各行各业，作光源、限位、定位检测，自动计数，测速，自动保护，工业自动流水线及微机信号，数控装置等应用，对提自控系统性和可靠性，具有巨大作用。
Ebs-60a is a two-stage running offset switch, which is widely used in various belt conveyors in metallurgy, coal, ment building materials, mining, electric power, port, metallurgy and chemical industries.
EBBS-60A two - stage deviation switch manufacturers.
EBBS-60A two - level running offset switch quality servi.
Range of application
Conventional belt conveyor, including flat belt conveyor and trough belt conveyor.
Underground and cable support belt conveyor.
Ship loading and unloading system, piling conveyor.
Technical parameters
Working voltage: 24VDC.
Contact capacity: 2 SPDT 400VAC 10A.
Secondary alarm level alarm: 20 ° 35 °
The scroll wheel Angle: 75 ° or less
Protection grade: IP67.
Ambient temperature: - 20 ℃ ~ + 80 ℃
Cable entran: 4*M20*1.5.
Cable specification: 6~12mm.
Product features
With address code, built-in RS485 bus transiver.
Communication baud rate can be encoded.
Standard modbus-rtu communication protocol.
Mechanical contact, no mperation.
Strong cast aluminum shell, electrostatic anticorrosion coating suitable for the installation of harsh industrial and mining environment.
Protection standard IP67 is also available in harsh environments; Exllent durability with high performan micro - switch and non - maintenan ball bearings.
Action bar bearing rated speed of 5000 RPM, applicable belt speed 6.35 m.
The maximum tilt Angle of the side roller is 75 degrees, so the protection switch will also be accurate when the conveyor belt is abnormal.
EBBS - 60 switch, a two-stage wandering wandering sensor suitable for belt conveyor, can make the belt conveyor at the edge of the belt run hang PianJiang cause serious wear and tear accident before they can send out alarm signals and further automatic parking.
To ensure the safety of the equipment and avoid the expansion of the accident in time, so as to ensure the production and protection of the equipment. In addition, because the signal can be sent to the control system, it is convenient to realize the automatic control of the factory, so it can achieve the efficiency of reducing staff, ntralize control, and facilitate the production and scheduling.
Matters needing attention
1. The deviation switch gear is vertical to the belt.
2. It is suggested that the distan between the steering wheel and the belt edge should be kept 120-160mm.
3. The base of the deviation switch is fixed firmly.
Ordering instructions
1. Optional acssories: mounting bracket.
Installation instructions
1, two levels of running deviation switch base Ф 12 mm hole on each side, near the belt conveyor Angle iron frame Ф 12 mm holes, using switch M10 x 30 mm screw fastening wandering.
2, installation running deviation switch should choose conveyer prone location of installation and application referen unit pross requirement, at the same time to consider effective spacing and thrust belt and catch wheel, it is recommended that the installation of the belt between the gear wheel and a distan of 120-160 - mm.
3. Installation distan: it is recommended to install a pair of running deviation switch every 50 meters.
4, running deviation switch factory is equipped with four core cabtyre cable length 0.5 meters, the core is equipped with a no., 2, 3, 4 line, which is suitable for normally open contacts are level 1, 2, alarm signal, 3, 4 for the normally closed contact is secondary stop signal.
EBBS - 60 switch, a two-stage wandering wandering sensors are widely used in machinery, machine tool manufacturing and food factory, textile, paper making, light industry, chemical industry, mining, metallurgy, aviation industry, electric power security, the automotive industry, Marine transportation, building, subway and so on all walks of life, as a light sour, spacing, positioning detection, automatic counting, speed, automatic protection, industrial automatic production lines and microcomputer signal, nc devi applications, such as to improve the autonomous system advanment and reliability, has a huge role.
